000110725 001__ 110725
000110725 005__ 20240319080958.0
000110725 0247_ $$2doi$$a10.1016/j.bsecv.2021.06.003
000110725 0248_ $$2sideral$$a127360
000110725 037__ $$aART-2022-127360
000110725 041__ $$aeng
000110725 100__ $$aÖzçelik, C.
000110725 245__ $$aDrastic microstructural modification of Bi2Ca2Co2Oy ceramics by Na doping and laser texturing
000110725 260__ $$c2022
000110725 5060_ $$aAccess copy available to the general public$$fUnrestricted
000110725 5203_ $$aBi2Ca2-xNaxCo2Oy materials with x = 0 = x = 0.125, have been prepared either by sintering through the classical ceramic method, or textured using the laser floating zone technique. XRD results have shown that Bi2Ca2Co2Oy phase is the major one, independently of the Na content, in both kind of samples. SEM studies have shown a drastic microstructural modification between sintered and laser-textured materials. Na-doping increases density and grain sizes in sintered materials, while it enhances grain alignment in laser-grown materials. Moreover, it decreases secondary phase content in all cases. Electrical resistivity is also drastically reduced through texturing, when compared to the sintered samples, and Na-doping further decreases it. The lowest values determined in the laser-textured samples (26 mO cm at 650 °C) are around 40% lower than the best in sintered materials. On the other hand, S has been only slightly affected for Na-doping or processing method for all samples. Consequently, the highest power factor at 650 °C (0.18 mW/K2 m) has been obtained in laser-grown 0.075Na-doped samples, which is around 20 and 70% higher than the measured in undoped laser-textured samples, and sintered ones, respectively. Se han preparado materiales de composición Bi2Ca2-xNaxCo2Oy, con x = 0 ≤ x ≤ 0,125, por el método de estado sólido, además de texturarlos mediante la técnica de zona flotante inducida por láser. Los resultados de XRD han mostrado que la fase Bi2Ca2Co2Oy aparece como la mayoriraria, independientemente del contenido de Na, en ambos tipos de muestras. Los estudios SEM han encontrado una drástica modificación microestructural entre materiales sinterizados y texturados. El dopado con Na aumenta la densidad y el tamaño de grano en materiales sinterizados, mientras que mejora la orientación de los granos en materiales texturados. Además, disminuye el contenido de fases secundarias en todos los casos. La resistividad eléctrica disminuye drásticamente con el texturado, en comparación con las muestras sinterizadas, mientras que el dopado con Na la disminuye aún más. Los valores más bajos determinados en muestras texturadas (26 mΩ cm a 650 °C) son alrededor del 40% menor que los mejores datos publicados en materiales sinterizados. Por otro lado, S solo se ha visto afectado levemente, tanto por el dopado como por el método de procesado. En consecuencia, el máximo factor de potencia a 650 °C (0,18 mW/K2 m) se ha obtenido en muestras dopadas con 0,075 Na y texturadas, que es alrededor de un 20 a un 70% superior al medido en muestras texturadas sin dopar y sinterizadas, respectivamente.
000110725 536__ $$9info:eu-repo/grantAgreement/ES/DGA/T54-20R$$9info:eu-repo/grantAgreement/ES/MINECO-FEDER/MAT2017-82183-C3-1-R
000110725 540__ $$9info:eu-repo/semantics/openAccess$$aby$$uhttp://creativecommons.org/licenses/by/3.0/es/
000110725 590__ $$a3.4$$b2022
000110725 591__ $$aMATERIALS SCIENCE, CERAMICS$$b6 / 29 = 0.207$$c2022$$dQ1$$eT1
000110725 594__ $$a4.4$$b2022
000110725 592__ $$a0.465$$b2022
000110725 593__ $$aCeramics and Composites$$c2022$$dQ2
000110725 593__ $$aMechanics of Materials$$c2022$$dQ2
000110725 593__ $$aIndustrial and Manufacturing Engineering$$c2022$$dQ2
000110725 655_4 $$ainfo:eu-repo/semantics/article$$vinfo:eu-repo/semantics/publishedVersion
000110725 700__ $$aDepci, T.
000110725 700__ $$aGürsul, M.
000110725 700__ $$aÇetin, G.
000110725 700__ $$aÖzçelik, B.
000110725 700__ $$0(orcid)0000-0003-3995-5763$$aTorres, M.A.$$uUniversidad de Zaragoza
000110725 700__ $$0(orcid)0000-0002-0794-3998$$aMadre, M.A.$$uUniversidad de Zaragoza
000110725 700__ $$0(orcid)0000-0001-7056-0546$$aSotelo, A.$$uUniversidad de Zaragoza
000110725 7102_ $$15002$$2305$$aUniversidad de Zaragoza$$bDpto. Ingeniería Diseño Fabri.$$cÁrea Expresión Gráfica en Ing.
000110725 7102_ $$15001$$2065$$aUniversidad de Zaragoza$$bDpto. Ciencia Tecnol.Mater.Fl.$$cÁrea Cienc.Mater. Ingen.Metal.
000110725 773__ $$g61, 6 (2022), 634-640$$pBol. Soc. Esp. Ceram. Vidr.$$tBoletin de la Sociedad Espanola de Ceramica y Vidrio$$x0366-3175
000110725 8564_ $$s1794277$$uhttps://zaguan.unizar.es/record/110725/files/texto_completo.pdf$$yVersión publicada
000110725 8564_ $$s2326282$$uhttps://zaguan.unizar.es/record/110725/files/texto_completo.jpg?subformat=icon$$xicon$$yVersión publicada
000110725 909CO $$ooai:zaguan.unizar.es:110725$$particulos$$pdriver
000110725 951__ $$a2024-03-18-13:48:58
000110725 980__ $$aARTICLE