Methodology for Clamping Load Measurement of Locking Systems Based On White Light Digitalization
Javierre, Carlos (Universidad de Zaragoza) ; Clavería, Isabel (Universidad de Zaragoza) ; Santolaria Mazo, Jorge (Universidad de Zaragoza) ; Elduque, Daniel (Universidad de Zaragoza)
Resumen: This paper presents a new methodology to measure clamping force of locking clips of a weatherproof luminary from the previous determination of its stiffness and the elongation they suffer under assembly conditions. Application of the methodology includes determination of the clip stiffness both experimentally and by FEM analysis, and measurement of the elongation by structured white light digitalization techniques.
Elongation values measured by white light are similar to those analyzed by conventional methods. The relationship between clips elongation and load applied is linear, so stiffness can be deduced from the slope of the curve. Results show that functionality of the clips can be achieved with different values of stiffness. There is not any direct relationship between clip stiffness and load performed by them because of the influence of initial length on the final load performed. Therefore, manufacturing tolerances must be taken into account to assure the proper performance of the clips.
Idioma: Inglés
DOI: 10.1016/j.measurement.2015.05.042
Año: 2015
Publicado en: MEASUREMENT 73 (2015), 494-502
ISSN: 0263-2241
Factor impacto JCR: 1.742 (2015)
Categ. JCR: INSTRUMENTS & INSTRUMENTATION rank: 22 / 56 = 0.393 (2015) - Q2 - T2
Categ. JCR: ENGINEERING, MULTIDISCIPLINARY rank: 22 / 85 = 0.259 (2015) - Q2 - T1
Tipo y forma: Article (PostPrint)
Área (Departamento): Área Ingeniería Mecánica (Dpto. Ingeniería Mecánica)
Área (Departamento): Área Ing. Procesos Fabricación (Dpto. Ingeniería Diseño Fabri.)
You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use. You may not use the material for commercial purposes. If you remix, transform, or build upon the material, you may not distribute the modified material.
Exportado de SIDERAL (2024-01-04-09:03:29)
Visitas y descargas
Elongation values measured by white light are similar to those analyzed by conventional methods. The relationship between clips elongation and load applied is linear, so stiffness can be deduced from the slope of the curve. Results show that functionality of the clips can be achieved with different values of stiffness. There is not any direct relationship between clip stiffness and load performed by them because of the influence of initial length on the final load performed. Therefore, manufacturing tolerances must be taken into account to assure the proper performance of the clips.
Idioma: Inglés
DOI: 10.1016/j.measurement.2015.05.042
Año: 2015
Publicado en: MEASUREMENT 73 (2015), 494-502
ISSN: 0263-2241
Factor impacto JCR: 1.742 (2015)
Categ. JCR: INSTRUMENTS & INSTRUMENTATION rank: 22 / 56 = 0.393 (2015) - Q2 - T2
Categ. JCR: ENGINEERING, MULTIDISCIPLINARY rank: 22 / 85 = 0.259 (2015) - Q2 - T1
Tipo y forma: Article (PostPrint)
Área (Departamento): Área Ingeniería Mecánica (Dpto. Ingeniería Mecánica)
Área (Departamento): Área Ing. Procesos Fabricación (Dpto. Ingeniería Diseño Fabri.)
You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use. You may not use the material for commercial purposes. If you remix, transform, or build upon the material, you may not distribute the modified material. Exportado de SIDERAL (2024-01-04-09:03:29)
Permalink:
Visitas y descargas
Este artículo se encuentra en las siguientes colecciones:
Articles > Artículos por área > Ingeniería de los Procesos de Fabricación
Articles > Artículos por área > Ingeniería Mecánica
Record created 2024-01-04, last modified 2024-01-04