Use of laser technology to produce high thermoelectric performances in Bi2Sr2Co1.8Ox

Rasekh, S. ; Costa, F.M. ; Ferreira, N.M. ; Torres, M.A. (Universidad de Zaragoza) ; Madre, M.A. (Universidad de Zaragoza) ; Diez, J.C. (Universidad de Zaragoza) ; Sotelo, A. (Universidad de Zaragoza)
Use of laser technology to produce high thermoelectric performances in Bi2Sr2Co1.8Ox
Resumen: Bi2Sr2Co1.8Ox bulk polycrystalline ceramics were prepared by conventional sintering of powders, obtained by polymer solution method and by directional growth using the laser floating zone technique. Microstructural analysis showed randomly oriented grains in the classical sintered materials, while in the laser-textured samples well oriented crystals with the c-axis nearly perpendicular to the growth direction were observed. A significant reduction on electrical resistivity, compared with the sintered materials, was observed due to the decrease on the secondary phases content. As a consequence, a raise on the power factor of about 2 and 5 times, compared with the classically sintered samples, was obtained for the as-grown and annealed laser-textured samples, respectively. The maximum power factor obtained at 650 °C in the annealed laser-textured samples (∼0.20 mW/K2 m) is much higher than the best value obtained in sinter–forged textured materials at the same temperature.
Idioma: Inglés
DOI: 10.1016/j.matdes.2015.03.005
Año: 2015
Publicado en: Materials & design 75 (2015), 143-148
ISSN: 0264-1275

Factor impacto JCR: 3.997 (2015)
Categ. JCR: MATERIALS SCIENCE, MULTIDISCIPLINARY rank: 44 / 270 = 0.163 (2015) - Q1 - T1
Factor impacto SCIMAGO: 1.844 - Materials Science (miscellaneous) (Q1) - Mechanics of Materials (Q1) - Mechanical Engineering (Q1)

Financiación: info:eu-repo/grantAgreement/ES/DGA/T12
Financiación: info:eu-repo/grantAgreement/ES/DGA/T87
Financiación: info:eu-repo/grantAgreement/ES/MINECO-FEDER/MAT2013-46505-C3-1-R
Tipo y forma: Artículo (PostPrint)
Área (Departamento): Área Expresión Gráfica en Ing. (Dpto. Ingeniería Diseño Fabri.)
Área (Departamento): Área Cienc.Mater. Ingen.Metal. (Dpto. Ciencia Tecnol.Mater.Fl.)


Creative Commons Debe reconocer adecuadamente la autoría, proporcionar un enlace a la licencia e indicar si se han realizado cambios. Puede hacerlo de cualquier manera razonable, pero no de una manera que sugiera que tiene el apoyo del licenciador o lo recibe por el uso que hace. No puede utilizar el material para una finalidad comercial. Si remezcla, transforma o crea a partir del material, no puede difundir el material modificado.


Exportado de SIDERAL (2026-01-27-15:07:25)


Visitas y descargas

Este artículo se encuentra en las siguientes colecciones:
Artículos > Artículos por área > Ciencia de los Materiales e Ingeniería Metalúrgica
Artículos > Artículos por área > Expresión Gráfica de la Ingeniería



 Registro creado el 2026-01-26, última modificación el 2026-01-27


Postprint:
 PDF
Valore este documento:

Rate this document:
1
2
3
 
(Sin ninguna reseña)